Blog

Washing Machine Tap Leaking

by | Nov 16, 2021 | Uncategorized

Fixing A Leaking Washing Machine Tap

The water intake valve on washing machines links the two water hoses to the device and adjusts the hot or cold water flow. A faulty valve could result in your washer refilling improperly or not at all. You can do nothing to rectify the valve itself, but you can regain complete water flow by cleaning the two input ports.

You can also test the valve to see whether it has failed. Fixing a faulty water valve is a straightforward task that must be completed using components and techniques unique to your washing machine type. Leaking laundry machine faucets loom as a possible unwelcome expense for you.

As a stealth destroyer, the fury of a leaking tap means your laundry’s cupboards, flooring, and walls are all vulnerable to damage. The most alarming aspect about leaky washing machine taps is that they are frequently identified only after significant harm has occurred. Many contemporary laundry designs conceal washing machine taps behind a cabinet or underneath the laundry sink for a more aesthetically appealing appearance.

While it is more pleasing to the eye and saves space, concealing taps from view can cost you if not monitored frequently. Read this article to realise how you can prevent plumbing issues as a result of a leaking washing machine tap and how to deal with it.

Leaking Washing Machine Tap Problems

As earlier stated, failing to maintain careful checks on non-visible laundry faucets may cause substantial discomfort and damages in your house, as well as an unwanted financial strain on yourself and your family. Always bear in mind that even a minor water leak can quickly escalate into a significant issue.

Washing machine tap leaks are frequently reported to cause plaster flaking, decaying of wood, and the growth of mould and mildew. These factors combine to provide a perfect habitat for termites, putting your entire home’s structural integrity in danger.

How To Prevent A Washing Machine Tap Disaster

If you have a leaky washing machine tap and it goes unnoticed, it can cause significant harm to your house. The following are some of the finest preventative approaches that you can turn to if you have a leaking washing machine tap:

  • Inspect the surroundings of the washing machine tap in your laundry regularly. Keep an eye out for any symptoms of wetness, discolouration, or swelling in the area.
  • When hiring a plumber for an unrelated repair, make sure to get a general check of your home’s tap system. Early detection of possible problems, such as washing machine tap problems, may be pretty beneficial in the long run.
  • Schedule a yearly visit to check for fundamental plumbing concerns, just as you would with the dentist or doctor. A case study on leaky washing machine taps and their possible consequences emphasises the significance of identification.

Cost-cutting is essential when trying to save, and as always, you should turn to prevention as opposed to finding a cure. Therefore, ensuring there are no persistent plumbing issues on your property is critical to preventing a costly plumbing emergency.

The Operation Of A Water Inlet Valve

The water inlet valve features two threaded ports that connect to hot and cold water hoses in the washing machine’s rear. Every port is regulated by a solenoid valve, which delivers electric power to open and shut the circulation of hot and cold water based on wash temperature settings and water-level switch signals. Water input valve faults can cause a washer not to fill correctly, fail to operate, or wash at an improper water temperature.

Fixing a water intake valve entails meticulously inspecting the parts till the problem is discovered. Cleaning the filter screens may suffice in some instances, but replacing the whole valve might be necessary.

Things To Do Prior To Fixing A Leaky Machine Tap

Before inspecting the water intake valve, you need to disconnect the washer from both its water and power supplies. Simply unplug the washer from the wall outlet and turn it off. On the home side of the water system hoses, turn off the hot and cold water valves.

Place a bucket on the floor with a rag beneath to collect the water from the supply hoses. Then, disassemble the hose connections to the washer’s ends from the washer. You can use a pair of pliers to loosen a hose connection if required.

To drain water from the hoses, place the loose end of each hose into the bucket. A bucket is essential in ensuring that you do not deal with water on the floor.

Repair Kit For Fixing A Leaky Washer Tap

Here are the tools you need to have in your repair kit to fix a leaking washing machine tap:

  • Bucket
  • Screwdrivers
  • Flashlight
  • Multimeter
  • Pliers
  • New water inlet valve (if needed)

Instructions For Fixing A Leaky Washing Machine Tap

Step One: Examine and clean the filter screen

Examine the filter screens in the water inlet valve for blockages, which might prevent water flow. This is the most prevalent cause of valve failure and the simplest to fix.

Examine each of the two hose-fitting ports on the water inlet valve with a flashlight – there should be a screen inside the port. If the screens are filthy, carefully clean them. Take care not to break the displays, as they are not replaceable.

Step Two: Put the inlet valve solenoids to the test

If blocked screens are not the issue, look for a faulty valve. Depending on the type of model of washer you have, you might need to remove the rear or front of the washer cabinet to access the cables on the water inlet valve. Open the cabinet’s back, top, or front, as needed, following the directions in the appliance owner’s handbook.

Once you access the valve, you will notice that each solenoid has two wires attached to it. Proceed to take them off one at a time and mark them so that you can reattach them appropriately.

Set the OHM X1 setting on a multimeter (also known as a volt-ohm metre) and test the solenoids for consistency by contacting one tester probe to one of the output terminals on each solenoid. The reading should show the resistance. If the measurement shows 0 resistance or infinity (), the solenoid is bad, and the valve should be changed. Separately test both solenoids; if any is defective, the entire valve must be replaced.

Step Three: Change the water inlet valve

Disassemble the screws that hold the valve to its housing or the washer’s back. Label the wires attached to the solenoid based on their colour and position. Then, pull the plugs apart to disconnect the wires.

Remove the intake valve from the inner pipe (or tubes) that supplies water to the tub. As per the type, it is generally held in place with a hose clamp, which you can remove with a screwdriver or pliers.

Make a note of the washer’s brand and model number, as well as the brand and component number of the water inlet valve, if you can find it. Using this information, locate a new valve at an appliance parts store. Reverse the disconnecting process to install the replacement valve.

Is A Laundry Box Present?

Follow the steps listed below to fix a leaking washing machine tap if your washer has a laundry box.

Step One: Cut out a rectangular piece of wall

You must cut out a rectangular portion of the wall to access the connections if the valves have been put in a plastic laundry box. If you have drywall, you can use a drywall saw to cut into it. In the same vein, if you have wooden walls, use a keyhole saw. Keep the cut-out to fix the wall.

Step Two: Apply the technique for replacing a threaded valve

If the connections are threaded, you can theoretically apply the technique for replacing a threaded valve, but your wrench might not fit. In this situation, a preferable option would be to hacksaw the supply pipe approximately 15 Centimetres below the box and remove the existing valve, pipe, and all. If the valve is soldered to the pipe, this is likewise the best method to apply.

Step Three: Install a new valve

Install a new valve by soldering or screwing it to a span of a new pipe. Pass the pipe through the groove in the washing machine box and connect it to the electrical supply using a sweat connector or a compression coupler. If you are lucky, you might not need to replace the valve at all.

Step Four: Tighten the nut

If the leak on your washing machine’s valve is from the handle, simply tighten the nut retaining the handle or change the handle packing.

Step Five: Turn off the water main

If you need to replace the handle packing, turn off the water in the laundry room, and disconnect the washer supply hose. Then, unscrew the packing nut directly below the handle and take off the handle. Replace the existing packing (which looks like string) from within the nut with fresh material. Finally, screw the nut back onto the valve and secure it, then you’re done.

NOTE: Make a point of having repair kits for your washing machine shut-off valve that includes everything you will need, based on the valve’s specifications.

Strategy For Repair Of Your Washer

So when the service term for the connecting hoses expires, there is no other option than to replace them. However, you do have an option when it comes to the valves. Each one’s mechanism is straightforward to comprehend and fix.

To stop water, a washer on the end of a compression screw clamps down onto a valve seat, and when the valve leaks, it’s generally since this washer – or the one fitting all around the handle, known as the packing washer – has worn out. To change either washer, simply turn off the water, remove the packing nut, and take out the valve stem if replacing the valve washer.

How To Clean Your Washing Machine’s Water Inlet Valve

Step One: Unplug the washing machine

Disconnect the washing machine from the power source.

Step Two: Adjust the machine’s position

Move the machine slightly away from the wall so that you can efficiently work behind it. If you take it out too far, you risk disconnecting the drain hose or damaging the water supply hoses.

Step Three: Turn off the water supply

To cut off the water supply, turn the water supply valves on the wall behind the washer clockwise. Supply valves will be installed at both the cold and hot water inlets.

Leaky Washing Machine Tap? Call A Professional!

In the laundry tub, washing machines draw water from your home’s water supply and mix it with detergent. After the wash cycle, the water is drained out, and the garments are rinsed and taken through a spin cycle to dry. Tiny particles of dirt, sand, and grit can occasionally be found in municipal water systems, which can cause your washer’s tap to leak.

Rust particles in pipes can also be found in older homes and cause leaks. That is why the inlet valves of washers include a screen. Cleaning the water tap valve in your washing machine at least once a year is a great technique to reduce the chances of leaks. As mentioned above, there are several ways to deal with a leaking washing machine tap. However, if your washing machine has plumbing-related issues that you cannot comprehend, call a professional to fix them for you.

Tags

Category

Related Articles